EV-2240-N3B (NTSC)
EV-2240-P3B (PAL)
Mini Indoor Dome Camera
480 TV lines
Small 37/16” (88mm) diameter
3.6mm lens
Automatic gain control
High dynamic range produces
images with accurate colors
Note: Model numbers that end with “Q” or that have a round green “Q” sticker signify RoHS-compliant products.
ENFORCER Mini Indoor Dome Camera
Overview:
Mounting screws
(not included)
Female BNC connector
DC plug with
Dome cover
Camera
DC jack
terminal block
(not included)
Before Starting:
1. Please read this manual carefully and keep it
for future reference.
5. Do not drop the camera or subject it to
strong vibrations.
2. Use the camera within given temperature and
electricity limits.
Note: Many video monitors produce strong
electromagnetic fields close to the display
CRT, especially when the monitor is turned
on or during de-gaussing, which occurs
automatically with many monitors when
turned on.
3. Do not point the camera at the sun. Heat could
damage the camera, even when not in use.
4. Do not mount the camera in areas exposed to
radiation, strong magnetic fields, or strong
electrical signals*
Installation:
1. Run hidden cables from the video source and
12VDC power supply to the camera. Do not
cut the DC jack or female BNC connector as
this will void the warranty.
5. Mount the mounting base to the wall using
4 mounting screws (not included). If
mounting to drywall or brick, it may be
necessary to use screw anchors (not
included).
2. Test to make sure the voltage is correct.
Use only 12VDC.
6. Adjust the camera angle as needed.
7. Test the video signal.
8. Reattach the dome to the camera.
9. Do a final test of the video camera
and monitor.
3. Carefully twist the dome from the base.
4. Hold the camera against the wall, ceiling, or
other mounting surface while watching the
monitor to find the best mounting location. Mark
that location with a pencil.
SECO-LARM U.S.A., Inc.
3
ENFORCER Mini Indoor Dome Camera
Troubleshooting:
Check that the camera is powered up.
Check that the power supply’s polarity is correct.
Check that the monitor is powered up.
The screen is blank.
Check that the video cable connecting the camera to the
monitor is connected properly.
Clean the lens using a soft, clean cloth.
Check that the light source is adequate.
The screen image is dim.
Change the position of the camera.
Change the position of the camera.
Change the position of the camera.
Check that the correct power supply is in use.
The screen image has poor contrast.
The screen image flickers.
The screen image is distorted.
The camera case is hot.
IMPORTANT
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and
statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this
product in violation of any current laws or statutes.
WARNING
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not open
the case of this device, as there are no field-serviceable components inside.
FCC COMPLIANCE STATEMENT
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to
part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his or her own expense.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a
period of one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of
any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is
not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or
property damages of any kind to the purchaser or anyone else.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is
one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without
notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2011 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part,
without the written permission of SECO-LARM.
SECO-LARM U.S.A., Inc.
E-mail: [email protected]
PICSN4
16842 Millikan Avenue, Irvine, CA 92606
Tel: 800-662-0800 / 949-261-2999
mi-EV-2240-x3B-1101.docx
4
SECO-LARM U.S.A., Inc.
|